Customers Reported...
Micaela (FITZROY NORTH VIC)
Repair Time: 5min
Difficulty: Easy
Parts used:
1541530
Comments:
Very easy - connect the 2 water tubes back on the water assy.
Tools Required:
no tools required
Colin (OCONNOR ACT)
Repair Time: 5min
Difficulty: Very Easy
Parts used:
1541494
Comments:
Unscrew the black end cap and remove the cap and filter cage from the machine. Pop the end cap off the old filter cage by rotating it 90 degrees and pull - it snaps onoff. Fit the new rubber seal to the filter cage and clip the black end cap back in place. Once assembled insert into the machine and tighten until a watertight seal is achieved.
Pliers help to tighten the end cap - the thread plastic on plastic is a poor design prone to damage through over tightening when trying to stop water leaks from worn seals. Weird stuff from the washing machine collects down here from pockets and can jam in the filter cage making it impossible to remove without damaging.
Tools Required:
Pliers
Raymond (LAMB ISLAND QLD)
Repair Time: 15min
Difficulty: Very Easy
Parts used:
1393431
Comments:
Remove top, disconnect and reconnect hose from pressure switch, flip machine on its back and remove hose on drum and reconnect.
Tools Required:
Phillips screwdriver and pliers.
Gareth (Seventeen Mile Rocks Queensland)
Repair Time: 15min
Difficulty: Very Easy
Parts used:
1393416
Comments:
Easy to fit but have to fiddle a little to get door off and back on so that it shuts correctly
Tools Required:
Screwdriver
Sharon (REDLAND BAY QLD)
Repair Time: 60min
Difficulty: Medium
Parts used:
276911
1541397
1393416
Comments:
Before you start just look at how it was assembled as the door lever needs to go on a specific way.
Tools Required:
Screwdrivers
Eric (LYNEHAM ACT)
Repair Time: 30min
Difficulty: Medium
Parts used:
1541526
Comments:
If the door cannot open - remove the top of the machine, to access the door latch use a flat head screwdriver to disengage the door, once the door has opened the door handle assy can be removed from the door, please be careful of the pins holding the handle that may come loose and must be reinstalled correctly, once the new handle is installed then proceed to reassemble the door.
Tools Required:
Phillips and flat head screwdriver
Paul (NEW AUCKLAND QLD)
Repair Time: 5min
Difficulty: Very Easy
Parts used:
1653964
Comments:
Part was easy to fit. 2 x multi plugs to plug in.
Tools Required:
Phillips head screwdriver to take top off of machine.
Lindsay (LAKE BOGA VIC)
Repair Time: 15min
Difficulty: Very Easy
Parts used:
1653964
Comments:
Simple to fit the new pcb just plug the wiring back onto the connectors (you cant get them wrong), hold the unit in place by the 3 locating knobs on the back of the pcb into the holes in the back plate of the machine while you screw the 2 holding screws into position. You will find that when you connect up the machine and turn the power on the machine will finish off the cycle it couldnt do when it broke down as mine had.
Tools Required:
Just a phillips head screwdriver
Tim (MARCOOLA QLD)
Repair Time: 15min
Difficulty: Very Easy
Parts used:
1492832
Comments:
Undo the screws and replace the pump
Tools Required:
Phillips head screwdriver
frans (KENDALL NSW)
Repair Time: 5min
Difficulty: Very Easy
Parts used:
1541476
Comments:
Very easy access to replace belt
Tools Required:
Phillips head screwdriver to remove 4 screws from backing plate
Can't find it? We can help
- PARTS (286)
- MODELS
PCB ASSY REAR OF MACHINE (Use Substitute P/N 1716937)
3.5021ratings
Location:
Loading...
SWITCH (DOOR LOCK)
5.0020ratings
Location: C0058
Loading...
WATER GUIDE ASSY
2.7522ratings
Location: R0021
Loading...
DOOR HANDLE (SILVER)
4.37131ratings
Location:
Loading...
DRAIN PUMP(replaces DC3130008D)
4.59257ratings
Location:
Loading...
BELT (DRUM DRIVE)
5.0010ratings
Location: U0095
Loading...
DRAIN HOSE (Use P/N 1655845)
Location: I0022
Loading...
FILTER CASE
5.0010ratings
Location: U0359
Loading...
PCB ASSY (PARTS - M)
3.507ratings
Location: C0115
Loading...
WATER VALVE
Location: W0032
Loading...
MOTOR, PUMP-DRAIN
4.22211ratings
Location:
Loading...
DIAPHRAM (DOOR)
2.004ratings
Location: U0029
Loading...
HOSE (WATER INLET - PRESSURE)
Location: I0003
Loading...
LEVER ASSY (DOOR)
Location: D0046
Loading...
SHOCK DAMPER (LOWER)
5.0010ratings
Location:
Loading...
MOTOR (DRUM)
Location: U0015
Loading...
OIL SEAL
Location: U0016
Loading...
R0030 WIRE ASSEMBLY (DIAPHRAGM)
4.008ratings
Location:
Loading...
PRESSURE SENSOR ASSY
Location: R0027
Loading...
DRAIN PUMP FILTER CAP
Location: R0047
Loading...
DRAWER BODY
Location: R0036
Loading...
CAP (RINSE)
Location: P0036
Loading...
COVER (DOOR)
Location: D0112
Loading...
DRAIN PUMP SEAL
Location: J0024
Loading...
Displaying 1 to 24 (of 286 parts)
Loading...
Exploded diagrams, Schematics and other documents
'); $.get(url, function(data, status){ $("#models-tab-pane").html(data); }).fail(function(xhr, status, error) { // error $("#models-tab-pane").html("Error: " + error); }); } function getProductPurchaseInfo() { // Collect product IDs var productIds = []; $('.product_purchase_info').each(function () { productIds.push($(this).data('products-id')); }); // AJAX POST request $.ajax({ url: 'product_purchase_info.php?cPath=26439_82481_64263', type: 'POST', data: {productIds: productIds}, // Sending product IDs dataType: 'json', success: function (response) { if (response.status === 'success') { // Update each product_purchase_info $('.product_purchase_info').each(function () { $(this).removeClass('d-flex justify-content-center align-items-center'); var productId = $(this).data('products-id'); if (response.data[productId]) { $(this).html(response.data[productId].pp_info); if(response.data[productId].mfr_info != ''){ $("#mfr-"+productId).html(mfrSvg() + response.data[productId].mfr_info); } } }); initUpdateCart(); } }, error: function (xhr, status, error) { console.error("AJAX request failed: ", status, error); } }); } function mfrSvg(){ return '
'; }
